It is essential to apply foundation waterproofing to prevent sump pump malfunctions and mold damage. Understanding how to waterproof a foundation will help you to determine which option is best for you.
Rubber membranes are ideal for waterproofing a basement as they are not only effective, but also eco-friendly because they contain no toxic substances and do not cause damage to surrounding property. They can be applied to both the internal and external surfaces of the foundation in order to prevent the ingress of not only water, but also air and insects.
Rubber is a convenient method as it can be applied by spraying or painting it onto the surface and require no priming. The result will be sufficiently flexible to maintain its ability with movement.
This clay-like is a good material to use as foundation waterproofing due to its ability to absorb water until it expands to its full capacity. It can take-in a significant amount of water and create a permanent seal once it has had its fill.
The panels which are formed from the material can be hammered or stuck
The foundation of your house shouldn’t require much work at all, if any. But when it does, it’s likely to be one of three culprits that needs fixing.
Condensation in the basement won’t seriously harm your foundation, so you could do nothing. If you want to prevent it, first make sure that all of the bathroom, kitchen and dryer vents in your home are venting to the outside.
If any of these air-exhaust vents runs through the basement, make sure all the pipe joints are airtight.
It may also help to insulate cold-water pipes in the basement. Otherwise a dehumidifier will solve the problem.
Cure hydrostatic pressure
Water pressing against your foundation is not a good thing — in extreme cases, it can collapse a wall — though water will usually start pouring through a crack first.
Hydrostatic pressure is so tremendous that coating and patches applied from the inside usually fail eventually, so it’s best to prevent hydrostatic pressure in the first place. Here’s what to check in order from simplest to most difficult to correct:
• Check to make sure that leaky gutters or downspouts
If you are planning to paint or to hang wallpaper, now is the time to examine your walls and ceilings and undertake the appropriate repairs.
1. When was your wall built?
Walls and ceilings built after the 1940s are likely to be made of wallboard, also known plasterboard.
Such walls are put together from rigid factory-made sandwich panels that are nailed to interior framing.
Typically 1.2 m (4 ft) wide, their seams and the nail heads holding them in place are covered with special tape and a plasterlike mixture known as joint compound.
Older, solid-plaster walls consist of several layers of true plaster applied wet on-site over a backing of wire mesh or wooden laths.
2. Know your limitations
Before you set out to repair problem walls or ceilings, know your limitations.
Minor cracks and holes left by picture-hanging nails are easy to handle for someone new to do-it-yourself repairs. But anything larger takes more preparation and a more practiced hand.
For tiny cracks and holes in plasterboard walls or ceilings (one cm,/1⁄2 inch or smaller), clean out the opening, apply spackling compound with a joint knife,
Rain gutters carry an appearance of simple design. The appearance of simplicity is one reason why homeowners usually pay little attention to them. They pick installation contractors without much thought, and accept whatever product they may bring to them. Once the gutter system is in place, they rarely take it seriously enough to clean it on a regular basis, or to inspect it to ensure good working order. In reality, however, rain gutters are anything but simple. These installations tend to be unforgiving of poor design and installation method, or neglect.
If you’ve never paid attention to your rain gutters, you should start now. Knowing your gutters better can save you considerable trouble in the future.
Getting through an inspection
The best way to understand the complexity of rain gutter systems is to actually get up there to take a look. A basic inspection can help greatly in letting you recognize areas of shortcoming t. Here are tips on areas to check out.
- Does your guttering have a downspout every 20 feet? If not, there could be overflows during heavy downpours.
- Stop up a downspout, put a garden hose into the rain gutter, and
One day your sink is draining fine, the next it is filling up with water. What a disaster! A clogged drain can sneak up on you fast, but there are some simple steps you can take every day to keep your drains clear. One of the easiest ways to clean a drain regularly is with baking soda and vinegar. Use a good amount of baking soda in the drain, then add plain white vinegar. It will foam while it cleans – this is good! After about a minute, run very hot water down the sink until you cannot hear any foaming. This is a great way to clean an unclogged drain and freshen the smell. Kitchen sinks are the most difficult to keep clear, but other sinks can have problems, too. Simple prevention, through care and cleaning, is the best way to keep your drains from getting clogged.
In your kitchen, be careful what goes down your drain. Try to avoid letting noodles and sticky foods get down your drain, especially if you do not have a garbage disposal. These foods can clog your pipes quickly, and sticky messes will grab more food to make bigger clogs. If you
Basement waterproofing is both an art and a science. Contractors can waterproof new or old basements. Basement waterproofing is defined as preventing water from penetrating into your basement area. Use Basement Waterproofing and Crawl Space Moisture Control If you have a wet basement or crawl space moisture problem of any kind. Companies can help seal your basement and prevent expensive structural damage to your home’s foundation.
In the past, drainage systems were not very efficient. Furthermore, new drainage systems can provide you with tremendous peace of mind with a Lifetime transferable warrantee included with some patented systems. Many systems come with lifetime transferable warranties. Learn more about professional waterproofing systems and do-it-yourself systems. This approach ensures you the best waterproofing systems and solutions available.
Concrete blocks, particularly cinder blocks, are more permeable to water vapor than poured concrete. Concrete paints, waterproofing sealers or paint like coatings are a temporary fix only. The problem of foundation crack repair and concrete crack repair has troubled and frustrated homeowners and builders for decades. Hydraulic Cement and these types of cement based products are a huge problem because it costs approximately 4 times the original product cost to remove them and decontaminate the concrete due to
Repairing cracks in a concrete wall is a simple procedure that can usually be completed within a day or so. Cracks that form in a concrete wall, particularly a basement wall due to settlement, frost heave or ground movement can be either structural or non-structural. The methods discussed in this article can be used to repair minor, non-structural cracks.
Clean and Prepare the Cracked Area
Before you undertake to repair the crack, use any combination of wire brush, vacuum or power washer to remove any oil, dirt or debris from the concrete wall surface and from inside the crack. The crack must be prepared so that the sealant will adhere to the crack surfaces. Do this by enlarging the crack using a concrete chisel and a hammer. Holding the chisel at an angle within the crack, chisel down to a depth of about 1 inch along the entire length of the crack. Reverse the angle and repeat the procedure. The objective is to create an inverted V shape below the surface, otherwise known as undercutting. The chiseled surface provides a stronger bond with the sealant and the diverging angle of the crack helps keep the sealant within the crack. Remove all loose
Proper maintenance and cleaning of your home’s gutters and downspouts is about more than simply keeping the exterior of your home looking nice. It may prevent damage to your home’s interior due to flooding through the foundation and walls or leaks in the roof due to seepage of water.
Gutters and downspouts should be cleaned and checked for signs of necessary repairs at least twice a year. Typically, the best times to do this are late spring and late fall. If you suspect a problem or live in an extremely rainy climate, then perhaps, you should check them more frequently.
Follow these procedures for all of the gutters and downspouts on your home.
Step 1 – Gather Tools and Pick a Starting Spot
Bring your tools and equipment to a location near your starting place. The corners of the home are good starting locations since this is where the downspouts are typically located. It’s best to start near the downspout and work away from it to avoid pushing additional debris into it.
Set the extension ladder on a level place. If you are using a bucket attached to the ladder with the s-hook for collecting the debris, attach it now. Otherwise, secure a plastic
Dry rot repair is crucial to preventing more damage to the infected wood. Dry rot is wood decay caused by a type of fungus that typically thrives with very little moisture. Common areas infected with dry rot are window sills, shutters, and roof run-offs. It can also be found in wooden outdoor furniture such as picnic tables and Adirondack chairs. Dry rot repair must be completed to prevent the spread of the fungus which will completely destroy the piece of infected wood.
Step 1 – Prepare the Work Location
Choose a warm dry day to complete any dry rot repair. You’ll likely have to complete the repairs outdoors, so it’s important to make sure the weather is warm and dry to allow the stabilizer and filler to dry.
Avoid making the repairs on a humid day, even if the temperature is warm. Work in a clean, well-ventilated area and make sure you have a place to dispose of the infected wood immediately. Dry rot is caused by a fungus, and you don’t want to spread the fungus when you’re doing the repair. Wear gloves, because most brands of wood stabilizer and wood filler are toxic.
Step 2 – Remove the Infected Wood
There are some DIY jobs that are best tackled early. Wait too long and you could end up with a bigger and more serious problem. Following are six things to repair around your home before it’s too late.
1. Rotting Siding and Trim
Rotting siding and trim will only get worse over time. Rot can spread to nearby areas, making a small project much bigger down the line. Rotting wood also invites pests, like carpenter ants, that will tunnel through perfectly dry wood and set up a nest in your home.
To replace rotting siding and trim you’ll need to remove the rotting piece and replace it with new wood. Make sure that when you remove the rotting piece, you cut into dry wood. That way you’ll be sure to eliminate further damage. If you aren’t comfortable doing the work yourself, you can hire a general handyman or carpenter.
2. Clogged Gutters
Cleaning the gutters is not a fun job. However, it’s an easy one that can prevent serious damage down the line. If your gutters are clogged with leaves and debris, it’s time to clean them out. Clogged gutters and downspouts prevent the flow of water when it rains. This water can
Never neglect to use waterproof paint to protect your basement against moisture. The basement is cooler when compared to the rest of the home, leading to dampness. If there are any imperfections in the foundation wall, then water will find a way to get into the basement.
Waterproof paint will not protect from a flood of water, but it will lessen the dampness, moisture, and mold. The following information will share several tips on how you can use waterproof paint to properly protect your basement.
Start With a Dry Surface
It may seem silly to want to have a dry surface in order to apply waterproof paint. In order for the paint to adhere to the surface, the wall must be dry. If it is not dry, moisture will simply be trapped in the material.Use a wet and dry vacuum to remove any water that has accumulated in the basement.
Dampness is also a factor. To combat that problem, use one or more dehumidifiers. How many you use will depend on the size of the basement. The dehumidifiers will leach the moisture from the air, which will dry the basement.
Applying waterproof paint to the basement walls is not a substitute for
If you’re a homeowner, you have probably encountered a basement wall leak at some point. The issue with these leaks, besides the obvious, is that they can be the source of harmful mold spores.
When you encounter a leak, it is best to take action and repair the problem as soon as possible. Fixing a basement wall leak is not an easy job; however, leaks and seepages can be prevented either before or after the basement is built. You only need to ensure that you take these measures before any leaks appear, since correcting a leak will take you a great deal of effort and time.
There are several reasons why a leak may have appeared. The workmanship could be poor. Cracks in walls or floors could have appeared while the house settled, and water pressure from outside might have built up, then forced itself through the walls.
Repair all holes and cracks in the building, then use a water-proofing compound to ensure that your wall is leak-proof. Fill hair line cracks with regular water-proofing mix; larger cracks should be cleaned and patched.
Use mortar to fill cracks and holes in cement or concrete walls. Before filling the crack, it is better
Carefully read these tips and instructions on how to waterproof your basement. Following the procedures which are outlined in this DIY article save both waste and effort while achieving superior results.
By reading this article, you will learn how to stop leak and seepage, repair holes and cracks, waterproof the walls and floors, and pack a leaking floor joint.
Stopping Leaks and Seepage
If you’re bothered with leaks or moisture seepage on your basement floor or walls, the problem can be solved. It takes time and effort, you have to do the job right.
There are 3 basic causes of seepage and cracks in basements. First, the original workmanship may be poor. Second, the house may have settled, causing cracks in either the floor or walls. Finally, water pressure from the outside may have accumulated and be forced water through the walls.
Such leaks are easy to detect. Moisture often begins to seep at the area where the floor and walls joins, or along cracks that may appear in the wall or floor.
Repairing Cracks and Holes Before Waterproofing
If there are no holes or cracks in the basement walls, you can apply a waterproofing compound directly to the walls by steps described later in
Having a waterproof basement is becoming a popular option for homeowners because it creates extra space to make into a guest bedroom, a work place, or an entertainment room.
Hiring a professional to waterproof the basement is costly. If a homeowner is savvy with home improvements, waterproofing the basement is an easy project if you follow these steps.
Step 1 – Covering up Cracks
Small cracks in the basement area (about 1/8-inch or smaller) should be repaired using waterproofing mix. Larger cracks should be cleaned and patched. Work gloves are recommended, as some harsh chemicals are used in the mixture.
Step 2 – Preparing the Mortar Mix for Filling
Mix the mortar with a consistency of 1-part cement to 2-parts fine sand. Mix the materials with the right amount of water to achieve the correct consistency. Apply the mixture with putty knife, apply the mortar into the cracks where water is seeping through the wall.
Step 3 – Chipping Process
Chip the broken areas with bigger holes. After chipping, fill the void with the mortar mix, and smooth the area with the trowel.
Step 4 – Filling the Cracks
A weep pipe should be inserted into the wall if water is trapped against the exterior
To waterproof a basement is a laborious task since you need to waterproof the basement walls and the basement floor. You also have to patch up all of the basement cracks that you find to inhibit water from coming into your basement. Hiring a professional plumber to do the waterproofing of your basement is expensive. Below are the materials that you need along with the instructions on how to waterproof a basement yourself and save money in the process.
Step 1-Repairing Holes/Cracks
Inspect the basement area to locate any holes and cracks. Repair very small cracks with waterproofing mix. Bigger cracks should be patched up using mortar mixture. Mortar mixture is combining one part cement to two parts fine sand with the right amount of water to create a mixture of somewhat firm constancy.
Step 2-Applying Mortar Mix
Brush on mortar mixture on cracks and holes where water gets absorbed into the wall using a trowel or putty knife. If pressure is seen that makes water enter the wall, break off the area by using a chipping chisel or hammer along the whole length of the crack and hole. Once chipping off is done, apply mortar mixture and level out the surface with a
Basement waterproofing is an important part of maintaining the health of a house. It prevents water from leaking into the basement and damaging walls, wood and foundation of the house. A damp and wet basement can also lead to mold growth and insect infestation.
It is good to hire a professional basement waterproofing company to protect your basement from water damage. Their experts will first determine the cause of the leak, then clean the area and waterproof it to make sure that it stays dry.
The type of waterproofing methods that your basement requires depends on the condition and the severity of the damage. Another factor determining the type of waterproofing method to be used is whether the cause of water damage is external or internal. Here is a brief overview of the types of basement waterproofing methods:
– Interior Sealants- It is used as a temporary measure to keep your basement dry. Available in spray forms, these sealants can directly be applied to the walls and floor of the basement. This prevents the walls and floors from absorbing moisture. It is cheap and effective waterproofing solution. It can be used as a temporary solution until you go for more permanent solution like
If you see cracks in your home’s foundation, a repair person should evaluate them as soon as possible. Some cracks are merely superficial, but others can pose danger.
Cracks in your home’s foundation can occur naturally from settling, and in many cases, tiny cracks don’t signal a larger problem. In other cases, however, cracks do indeed pose a significant problem. So how can you tell the difference?
Read on to learn more about this common problem and when you should consult a professional.
What Is a Slab Foundation?
Home builders use several types of support systems, depending on soil conditions and architecture styles. The most popular foundation today is the monolithic concrete slab.
A slab foundation is made up of a single layer of concrete poured several inches thick, and thicker at the edges in order to form footings. It is further strengthened by reinforcing rods of metal rebar. Slabs are normally poured on top of a bed of crushed gravel in order to provide adequate drainage. In many cases, plumbing and electrical lines are located within the slab itself.
This type of foundation works best in areas where the ground does not freeze, but it can be adapted to suit other areas.
Indoor Warning Signs of
Weather-proofing your home makes your heating and cooling systems more efficient and keeps your costs low. Here are some smart ways to get started.
Consider draft-proofing your home
Incoming drafts at any time of the year reduce comfort and add to heating and cooling costs.
Draft-proofing is usually the cheapest and easiest form of energy improvement as most jobs can be carried out using simple materials.
Heat leaks and drafts are likely to occur through unused fireplaces and chimneys, openings around doors, gaps between windows and frames, gaps between walls and skirting boards, and building joints.
The right way to seal a fireplace
Fireplaces can be sealed when not in use by placing a damper in the throat of the chimney and closing it, or by installing a panel in a fireplace opening.
How to seal windows and doors
Windows and doors can be sealed against the weather in a number of ways:
Openings and cracks around doors and windows can be sealed using draft stoppers which are strips of rubber or foam fixed to an edge or frame and designed to compress or overlap sufficiently to make a tight seal. Adhesive weatherseals are available in a variety of shapes and can achieve the same purpose.
Don’t rush into designing your house all at once. These tips will help you take your time at each step to make sure the details are exactly what you want, eliminating stress and potential regret down the road.
1. The first, basic step
Layout of space can begin with a series of very informal module or “bubble” sketches. Each module represents a particular use of space. The more of these diagrams you draw, the nearer you are likely to come to sensing the best floor plan. You should also make a point of visiting and examining the general layout of as many homes as possible.
2. Going into detail
A sketch of floor plans, with rooms in approximately correct proportion, follows the space layout. With such sketches, details of regular patterns of personal movement can be discerned well enough to reveal defects in the location of doorways.
3. Dealing with regulations
For final plans or working drawings you will need a diagram of each elevation, and a plan of each separate floor. This is usually drawn in a 1:100 scale. If you are on a small block of land, you will need a site diagram showing the house, with distances from boundaries and building
If you have a flat roof, it won’t shed water as quickly. This is why it’s extra important to protect from leaks. Follow these seven tips to protect your flat roof.
1. Inspect regularly
Every few months, inspect your flat roof. Depending on the architectural style of your home, you may be able to inspect your flat roof by looking out a second-story window.
In other cases, you’ll have to access your roof by climbing a ladder.
Look for holes, tears, blisters, and loose seams on an asphalt-roll roof or for rust and pitting on a metal roof. Make repairs or add patches to prevent leaks.
Also check the edges of the flashing to make sure water can’t seep under it.
2. Use protective paint
To protect an asphalt-roll roof against damage from the sun’s ultraviolet rays, paint it with reflective asphalt aluminum paint. The paint will also lubricate the roofing and reseal the surface against water.
3. Reviving the surface of the roof
After a while, many asphalt roofs become a patchwork of repairs. If this is true of yours, revive the surface by simply brushing on asphalt roof coating.
If the roof has any slope at all, start at the highest part and work